This Post

 

 

How do you really feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Setting up a tub isn't exactly rocket science, but it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily available, the project can move quickly; if you have to open a wall to remove the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed task, it is far better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will aid you mount a new tub in your bathroom if you have currently acquired a brand-new tub and do not require to alter the plan of your previous supply of water pipes.
Your devices as well as material checklist need to consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installment

To start with, the supporting frame provided with the bath should be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will come from the pipelines. Once the supply pipes have actually been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Setting up the Tub

Making use of both wooden boards under its feet, place the tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the bath tub till the level reviews level.
To install taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the supply of water as well as check all joints and new pipework for leakages and also tighten them if needed. Fill up the bath tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub must wait up until the bathtub has been made use of at the very least once as this will resolve it right into its final position.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be connected to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the location where the bath fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also grout.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

We are very drawn to Tools You Need to Install a New Bathtub and I am hoping you enjoyed the entire article. Enjoyed reading our article? Please share it. Let others check it out. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Get An Estimate