Book Your Appointment

 

 

Are you currently interested in details concerning How to Install a Bathtub Yourself?

Setting up a tub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately challenging task. If the old bathtub is readily easily accessible, the project can relocate immediately; if you have to open a wall surface to eliminate the old bathtub and place the new bath tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have actually qualified yourself for the work and fit trying it. Rather than working with a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Chances are you might need a specialist plumber to make tube links.
This article will help you set up a brand-new bath tub in your restroom if you have actually currently gotten a new bathtub and don't require to change the plan of your previous supply of water pipes.
Your devices and product list should make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installation

First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipes have been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Before going on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Setting up the Bath tub

Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are practical in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the bathtub till the level reads degree.
To mount taps, fit all-time low of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the water system and also examine all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and likewise check the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bath tub should wait up until the tub has actually been utilized a minimum of once as this will resolve it right into its final setting.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Protect the tap in position with the manufacturer supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former kind must be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bathtub

In the location where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, resulting in problems with dampness and also possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub is in use. The sealant can crack rather early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed our section on How to Install a Bathtub Yourself. Thanks a ton for taking the time to browse our posting. Loved our piece of writing? Please share it. Let others locate it. Thank you for going through it.

Give Me A Quote!